Hi Sharp Dvr Reset Password New May 2026

Most DVRs have internal reset jumpers or a “Reset” button on the main board:

This will reset all settings, including password, IP, and recording configuration. Recordings usually remain on the hard drive, but the DVR will treat them as “foreign” until you re‑initialize the disk (which may erase them).

Important: If the DVR is installed at a business or belongs to someone else, make sure you have permission to reset it. Unauthorized access may violate laws or company policies.

To reset the password for a Hi Sharp DVR (New Model), you can typically use the built-in "Dynamic Code" feature or the official password retrieval process. If your device is brand new or recently reset, the default login credentials are usually admin / 123456.

Method 1: Using the "Dynamic Code" (Recommended for New Models)

Newer Hi Sharp models include a self-service recovery option via the local interface. Navigate to the login screen on your DVR monitor. Click on "Forget Password" or "Retrieve Password".

Select the "Dynamic Code" page to generate a unique code or QR code on the screen. Take a screenshot or photo of this dynamic code.

Send the image, along with your model number and serial number, to your regional distributor or directly to Hi Sharp Support at sales@hisharp.com.tw.

They will provide a temporary recovery code to unlock the device and set a new password. Method 2: Initial Setup & Default Credentials

If you are setting up the DVR for the first time or after a successful factory reset, use these default settings: Username: admin Password: 123456 hi sharp dvr reset password new

Action: Upon first login, you will likely be prompted by a Wizard Setup to create a strong, unique password. Method 3: Hardware Reset (If Software Fails)

For models where you cannot access the software reset menu, a physical reset on the motherboard may be necessary.

Internal Reset Button: Some units have a small button on the mainboard. Press and hold it for 5–10 seconds while the unit is powered on until you hear a long beep.

Jumper Pins: If there is no button, look for two metal pins labeled "TP" or "J1". Use a screwdriver or tweezers to short-circuit these pins while powering on the device. Hold for roughly 60 seconds to restore factory defaults. FAQ - Support | HI SHARP INTELLIGENCE

Since Hi-Sharp DVRs often run on modified generic firmware, they are frequently compatible with popular CCTV password reset tools found on the Google Play Store or Apple App Store.

Recommended Apps:

You can also use the Hi Sharp DVR software to reset the password. Here's how:

New Hi Sharp DVR Models: Additional Reset Methods

Newer Hi Sharp DVR models may have additional reset methods, including: Most DVRs have internal reset jumpers or a

Once you have successfully performed the "hi sharp dvr reset password new" process, you must secure the system again:

Alternative: On some Hi Sharp boards, there is a small circular battery (CR2032). Removing this battery for 5 minutes also resets the BIOS and password.

To reset the password on your Hi Sharp DVR , try the following official and technical recovery methods: 1. Try Default Credentials

If the DVR is new or has been reset recently, try these common default login details: Username: admin Password: 123456, admin, or leave it blank 2. Use the "Retrieve Password" Feature (Dynamic Code)

Most modern Hi Sharp recorders include a built-in recovery tool on the login screen: Go to the Login interface on your DVR monitor. Click on Forget Password or Retrieve Password. Select the Dynamic Code or Dynamic Password option.

Take a photo of the dynamic code page or QR code that appears.

Email this photo along with your model and serial number to sales@hisharp.com.tw or your regional distributor to receive a temporary unlock code. 3. Hardware Factory Reset

If software methods fail, you may need to perform a hardware reset:

Reset Button: Check the back or the internal motherboard for a small push button. Press and hold it for approximately 35–40 seconds while the device is powered on until you hear a beep. This will reset all settings, including password, IP,

Battery Removal: Power off the unit, carefully remove the CMOS battery from the motherboard for a few minutes, power the DVR on and then off again, and reinsert the battery. This can sometimes reset the internal clock and password on older models. 4. Technical Support Contact

If you cannot generate a dynamic code, contact Hi Sharp directly through their Official Support FAQ or via email at sales@hisharp.com.tw.

Which Hi Sharp model are you using? I can give you more specific button locations if you have the model number. How to Reset DVR Password

Before diving into complex resets, try these factory defaults. Hi Sharp uses several variants:

If this works: Immediately go to Settings > System > User and create a new strong password. Write it down physically.

If the software backdoors are sealed, you must go analog. This involves opening the DVR case.

Warning: This will void any warranty and involves handling electronics.

The Battery Pull (The Brute Force Way):

Note on modern units: Some newer DVRs store the password in non-volatile flash memory (like an SD card or a chip). Removing the battery will not work on these units; you must find the reset jumper or use the software hash method.