Hi Sharp Dvr Reset Password Upd May 2026
📞 If none work: Look for a sticker inside the case or on the bottom – many Hi Sharp devices print the default password there.
When the software method fails, you must physically open the DVR. Warning: This erases ALL settings, including network configurations, camera channels, and passwords. Recorded video on the hard drive usually remains, but you may need to re-add the drive.
If you are locked out of your Sharp DVR, the method to reset the password depends heavily on the specific model and the firmware version installed. Most Sharp DVRs are rebranded OEM units (often manufactured by companies like Dahua or OEM generic brands), meaning the interface may vary.
Here are the three most common methods to reset the password:
Final tip: Once you regain access, write down your new password and store it securely. Consider setting up security questions if available.
If you have forgotten your Hi Sharp DVR or NVR password, you can reset it by following the manufacturer's official "Dynamic Code" procedure. Because Hi Sharp devices often require dealer-level authorization for security, you will likely need to coordinate with your regional distributor. Method 1: Using a Dynamic Code (Recommended)
This is the standard software-based reset for modern Hi Sharp recorders.
Locate Password Reset: On the DVR/NVR login screen, click on Forgot Password.
Navigate to Retrieve Password: Go to the Retrieve Password section and select the Dynamic Code page.
Capture the Code: Take a clear photo or screenshot of the Dynamic Code and the QR code (if displayed) on your monitor.
Contact Support: Send this image, along with your device's model number and serial number, to your regional distributor or seller.
If you cannot find your seller, you can contact sales@hisharp.com.tw for assistance.
Enter the New Code: Once support provides a one-time dynamic password, enter it into the DVR to gain access and set a new permanent password. Method 2: Default Credentials
If the device has never been configured or was recently factory reset, try the factory default credentials: Username: admin Password: 123456 Method 3: Physical Reset (Hardware)
For older models or if software methods fail, some devices have physical reset options:
Reset Button: Check the back or the internal motherboard for a small Reset button or pinhole. With the power on, press and hold this button for 5–30 seconds until the device reboots. hi sharp dvr reset password upd
G1 Jumper: Some boards feature two pins labeled G1. Shorting these pins with a conductive material while powering on the device and waiting for 60 seconds may trigger a factory reset. Summary of Important Details Information Official Site Hi Sharp Support Support Email sales@hisharp.com.tw Required Info Model Number, Serial Number, Dynamic Code Screenshot FAQ - Support | HI SHARP INTELLIGENCE
Disclaimer: This information is for educational purposes and to assist owners in recovering access to their own devices. Attempting to bypass security measures on devices you do not own is illegal.
Before doing a hard reset, try these common default combinations:
If none of these work: Contact Sharp Support or the vendor you purchased the unit from. They often have specific "Master Passwords" based on the serial number or MAC address of the unit, which they can provide to verified owners.
Note: Hi Sharp devices are often rebranded OEM units (frequently using HiSilicon chips). The most common method below works for 90% of models. If it fails, check for a physical reset button on the motherboard.
Warning: Resetting a DVR may erase settings or recordings. Back up video/settings if possible.
Quick checklist to gather before contacting support or service:
If you want, tell me the exact SHARP DVR model number and whether you have physical access to the unit (monitor + mouse) and I’ll give step-by-step model-specific options.
Related search suggestions provided.
If you are setting up the device for the first time or if it was recently factory reset, it may still be using the manufacturer's default settings. Default Username: admin Default Password: 123456
Alternative Passwords: Try 1234, admin, 888888, or leaving the password field blank. 2. Request a Dynamic Recovery Code
Modern Hi Sharp recorders (NVRs and DVRs) feature a "dynamic code" recovery method. This is the most secure and recommended way to reset a forgotten password. Navigate to the System Login screen on your DVR. Click on Forget Password or Retrieve Password.
Locate and click the Dynamic Code page. A unique recovery code or QR code will appear on the screen.
Take a photo of this page, ensuring the serial number and current system date are visible.
Send this information to your regional distributor or contact Hi Sharp official support at sales@hisharp.com.tw. 📞 If none work: Look for a sticker
Once they verify your ownership, they will provide a temporary master password valid for that specific date. 3. Hardware Reset (Internal Button or Jumper)
If you cannot access the software menu, you can perform a hardware reset by opening the unit. Note: Opening your DVR may void its warranty. FAQ - Support | HI SHARP INTELLIGENCE
Resetting Password on Hi Sharp DVR: A Step-by-Step Guide
Hi Sharp DVR (Digital Video Recorder) devices are widely used for surveillance and security purposes, offering high-quality video recording and playback features. However, there may be instances where you need to reset the password on your Hi Sharp DVR, such as when you forget the current password or when the device is being used in a new setup. In this article, we will walk you through the process of resetting the password on your Hi Sharp DVR.
Precautions Before Resetting Password
Before you proceed with resetting the password on your Hi Sharp DVR, make sure to take the following precautions:
Method 1: Resetting Password using the Web Interface
This method involves using the web interface of your Hi Sharp DVR to reset the password. Here's how:
Method 2: Resetting Password using a USB Drive
If you're unable to access the web interface or prefer a more straightforward method, you can use a USB drive to reset the password. Here's how:
Method 3: Resetting Password using the DVR's Button
Some Hi Sharp DVR models have a reset button that allows you to reset the password. Here's how:
Common Issues and Solutions
Conclusion
Resetting the password on your Hi Sharp DVR is a straightforward process that can be completed using the web interface, a USB drive, or the DVR's reset button. Make sure to take the necessary precautions before resetting the password, and if you encounter any issues, refer to the troubleshooting section or contact the manufacturer's technical support. By following these steps, you'll be able to reset the password on your Hi Sharp DVR and regain access to your device. When the software method fails, you must physically
To reset the password for a Hi Sharp or generic Sharp DVR, you can use built-in recovery options like dynamic codes, official support tools, or physical hardware resets. 🔑 Common Default Credentials
Before performing a hard reset, try these common default login combinations: Username: admin or Admin Passwords: 123456, admin, Admin, or just leave it blank. Other defaults: 111111, 000000, or 888888. 🛠️ Method 1: Use the "Dynamic Code" (Official Method)
Most modern Hi Sharp DVRs/NVRs include a "Forgot Password" feature on the login screen. Click Forgot Password on the login interface. Navigate to the Retrieve Password or Dynamic Code page.
Take a photo of the dynamic code/QR code displayed on the screen.
Send the photo, along with your model number and serial number, to Hi Sharp Support (sales@hisharp.com.tw) or your regional distributor.
They will provide a temporary unlock code to reset your admin account. ⚡ Method 2: Physical Hardware Reset
If you cannot access the menu, you can force a factory reset using the internal board.
External Reset Button: Look for a small pinhole on the back or bottom. Press and hold with a paperclip for 5–30 seconds while the device is powered on.
Internal Jumper: If there is no button, you may need to open the casing and locate two pins marked "RESET" or "CLR". Turn off the power. Use a screwdriver to short the two pins (connect them).
Power the unit back on while holding the short for 30 seconds. The DVR will beep or reboot to the setup wizard. 📱 Method 3: Mobile App Recovery
If you previously linked your DVR to a mobile app like Hi Sharp EX or Superlive Plus: Open the app and go to Reset Device Password.
Use the app's scanner to scan the QR Code from the DVR's login screen.
You will receive a verification code via your registered email. Enter that code on the DVR to create a new password.
📌 Pro Tip: If your DVR is an older generic model (often labeled "H.264 Network DVR"), the master password might be generated based on the date shown on the screen. FAQ - Support | HI SHARP INTELLIGENCE
Most Hi Sharp DVRs have a Security Question feature.