Tgc Bc901h Manual May 2026

| Code | Meaning | |------|---------| | E01 | Battery voltage exceeds safe limit | | E02 | Internal temperature >60°C | | E03 | Output short circuit | | E04 | Charging timeout (>24h) | | E05 | Battery disconnected during cycle |

If you need the official original manual in PDF, search for:
"TGC BC901H manual PDF" or check the manufacturer’s support page. For specific troubleshooting of your unit, provide the exact error message or behavior, and I can help further.

TGC BC-90-1H (often referenced as BC901H) is a wired remote control used for TGC (Towngas)

instantaneous gas water heaters in Hong Kong. It allows users to control water temperature and system functions from the bathroom. www.towngasappliance.com Core Functions & Controls On/Off Button

: Powers the heater on or off. When turned on, the temperature display and operation indicators light up. Priority Button & Indicator

: Used to gain control over the system when multiple remotes (e.g., kitchen and bathroom) are installed. Priority Indicator lights up when that specific remote has control.

If the indicator is flashing, control cannot be transferred because the heater is currently in use. Temperature Adjust Buttons buttons to set the desired hot water temperature. : Typically adjustable from 35°C to 60°C High Temp Warning High Temperature Indicator lights up if the setting is 50°C or higher to warn against scalding. Preheat Button (Optional)

: On compatible models, this activates a circulation function to ensure hot water is available immediately at the tap. www.towngasappliance.com Status & Operation Indicators Green Light : Indicates the heater is in Yellow Light : Indicates the heater is currently and burning gas. Digital Display : Shows the set temperature or Error Codes if a malfunction occurs. www.towngasappliance.com Troubleshooting Common Issues Potential Cause / Action No Hot Water

Check if the gas supply valve is open and power is connected. Cannot Change Temp Ensure the light is on for your remote. Error Code Displayed Note the number (e.g., "11" for ignition failure) and call Towngas Customer Service Low Water Flow Check the shower head or cold water filter for blockages. Safety & Maintenance Tips Avoid Scalding

: Always test the water temperature with your hand before stepping into the shower. : Wipe the remote with a soft, damp cloth. Do spray water directly onto the unit or use solvents. Long Absence

: If the heater hasn't been used for over a week, run the hot water for at least one minute to flush the pipes before use. www.towngasappliance.com For complete official documentation, you can refer to the TGC User Instructions provided by Towngas Appliance www.towngasappliance.com Are you seeing a specific error code on your remote display that you need help deciphering?

TGC BC-90-1H (often referenced as BC901H) is an optional bathroom remote control designed for use with TGC Gas Water Heaters

. It allows you to adjust water temperature and manage heater functions directly from your bathroom. www.towngasappliance.com Key Controls and Features On/Off Button:

Press to start or shut down the heater. The temperature display and operation light will illuminate when active. Priority Button & Indicator: tgc bc901h manual

Used to gain control over temperature settings. When the light is on, this remote has "priority" for adjustments. If the indicator flashes, priority cannot be transferred (usually because water is currently running). Temperature Adjustment:

Use the "Up" and "Down" arrows to set the water temperature. The standard range is typically 35°C to 60°C Preheat Button (Optional):

If your specific heater model supports a preheat loop, this button activates the circulation to ensure hot water is ready at the tap. High Temperature Indicator: Lights up when the water temperature is set to 50°C or higher as a safety warning for scalding. www.towngasappliance.com Operation Guide

button. The default temperature upon first use is typically 42°C. Take Control: If the "Priority" light is off, press the Adjust Water:

Press the arrows to your desired heat. For safety, if the temperature is set above 50°C, the display may flash. Use Water:

Open the tap; the burner ignites automatically, and the operation light turns orange or yellow. www.towngasappliance.com Troubleshooting Common Error Codes

If an issue occurs, a number will flash on the remote's display: www.towngasappliance.com

Ignition failure. Check if the gas supply valve is fully open and try restarting the power.

Often related to the preheating circulation; ensure water supply isn't interrupted. Resetting:

Close the hot water tap, wait 10 seconds, and try again. If the code persists, turn the power off for 10 seconds before restarting. www.towngasappliance.com Safety & Maintenance Scalding Risk:

Always check water temperature with your hand before stepping into the shower, especially if a different remote (e.g., in the kitchen) recently had priority.

Use a damp, soft cloth to wipe the remote. Avoid using solvents or spraying water directly onto the unit. Long Absence:

The TGC BC-90-1H Go to product viewer dialog for this item. is a specialized bathroom remote control unit used with Towngas instantaneous gas water heaters in Hong Kong. It allows users to control water temperature and system functions directly from the bathroom. Key Controls and Indicators | Code | Meaning | |------|---------| | E01

Power Button (開/關): Used to start or shut down the water heater. When activated, the temperature display and "Priority" indicator will light up.

Temperature Setting (水溫設定): Buttons to adjust the hot water temperature.

Priority Button & Indicator (優先): Press this to take control of the water heater from other remotes (like a kitchen unit). The indicator lights up when this remote has control.

Operation Indicator (運作): This light is green when the system is on standby and turns yellow when hot water is being actively used.

Preheat Cycle (預熱循環): Starts the preheat function to ensure hot water is available quickly; the maximum preheat temperature is typically capped at

High Temp Indicator (高溫): A warning light that illuminates if the water temperature is set to or higher. Basic Operation Steps Turn On: Press the Power button on the BC-90-1H.

Gain Control: Ensure the Priority light is on. If not, press the "Priority" button to transfer control to the bathroom.

Set Temperature: Use the adjustment buttons to reach your desired heat.

Use Water: Open the hot water tap. The burner will ignite automatically, and the Operation light will turn yellow. Safety and Troubleshooting

Scald Prevention: Always check the water temperature by hand before showering.

Error Codes: If the system malfunctions, a numeric error code will flash on the temperature display.

Priority Lock: You cannot change the Priority control while hot water is currently running.

Automatic Shut-off: The unit includes safety features like flame failure protection, overheat protection, and pressure relief valves. If you need the official original manual in

For official support or repairs, you can contact the Towngas Customer Service Hotline at 2880 6988.

| Parameter | Description | Range | Default | |-----------|-------------|-------|---------| | F01 | Temperature differential (hysteresis) | 0.5°F – 5°F | 1.0°F | | F02 | Compressor short-cycle delay | 2 – 10 min | 5 min | | F03 | Sensor type (internal/external) | 0=Internal, 1=External | 0 | | F04 | Temperature calibration offset | -9°F to +9°F | 0 | | F05 | Backlight timeout | 0 (always on) to 60 sec | 15 sec |

To change: Use ▲/▼ to select parameter, press SET, adjust value, press SET to store. Exit by pressing MENU repeatedly.

⚠️ Changing F01 (differential) to too low a value can short-cycle your compressor. TGC recommends keeping it at 1°F for residential HVAC.

If the manual does not resolve your problem, TGC customer support should be your next step. Because TGC products are often rebranded by other sellers, finding direct support can be tricky.

Options:

Before calling, have this information ready:

The BC901H is designed for heavy-duty financial use. Here is a quick guide to the primary keys you’ll need for daily operation:

If you’ve recently purchased a TGC BC901H device—whether it’s a smart thermostat, a sophisticated battery charger, or an industrial control unit (depending on the product line, as TGC produces varied electronics)—you know that the included printed “quick start” guide often leaves much to be desired. Finding a complete, easy-to-read tgc bc901h manual can be a challenge.

This article serves as your comprehensive digital manual. We will cover initial setup, advanced programming, common error codes, maintenance, and troubleshooting. By the end, you won’t need to dig through a drawer for that tattered booklet.

If you purchased the TGC BC901H from Amazon, eBay, or a specialty battery store, check your order history. Many sellers provide a direct link to the tgc bc901h manual PDF in the product description or post-purchase email.

Overall Verdict: 4.2/5
One of the better manuals in the sub-$500 CNC category. It won’t win design awards, but it will get you cutting wood safely.

As someone who has assembled half a dozen Chinese CNC routers (Genmitsu, FoxAlien, Sainsmart), I judge a machine by its manual first. The TGC BC-901H manual is a pleasant surprise. It’s not perfect, but it avoids the usual pitfalls of Engrish, missing steps, and dangerous electrical guesswork.