Traice | Dvr Password Reset

If you want, provide the exact Traice DVR model number or a photo of the unit’s label and I’ll give model-specific reset steps and the likely default credentials.

Related search suggestions:

Some Traice DVR models have a small reset button on the main circuit board.

Warning: This will erase all settings (network IP, motion detection zones, camera names). Recordings on the hard drive are usually preserved.

Pro Tip: If you cannot find the official tool, contact the seller on Amazon, eBay, or AliExpress. Send them a photo of your Security Code screen. They will often generate the unlock code for free.

To reset the password for a Traice DVR , you typically follow procedures common to many OEM security systems, such as physical hardware resets or using a dynamic super password based on the device's system date. 1. Physical Hardware Reset

Most Traice and similar OEM DVRs have a physical method to revert to factory settings: Reset Button: traice dvr password reset

Check the motherboard inside the unit for a small push-button. Power off the DVR. Press and hold the reset button.

Power the DVR back on while continuing to hold the button for about 15–30 seconds.

The system should reboot to the initial setup screen, allowing you to set a new password. Pinhole Reset:

Some models feature a pinhole on the back or front panel. Insert a paperclip and hold it for 10 seconds while the unit is powered on. 2. Default Credentials

If the unit has already been reset or is new, try these common default login combinations: Usernames: Passwords: 3. Software/Dynamic Password Reset

If physical access is limited, you can often use a "Super Password" generated by the DVR's internal date: Date-Based Password: If you want, provide the exact Traice DVR

Note the current system date shown on your monitor (e.g., 2024-04-14). Use a DVR password generator tool (often found online for "H.264" or "XMeye" based systems) to create a temporary code for that specific day. SADP Tool: If the Traice unit is an OEM of Hikvision, use the

to export a "Forgot Password" file and send it to technical support to receive a reset key. 4. Technical Support Contact

If these methods fail, Traice often requires a serial number and the current system time to generate a secure unlock code. You may need to contact your local installer or the vendor's tech support email with: Model Number Serial Number (found on a sticker on the bottom or back) The exact date/time currently displayed on the DVR monitor. EverFocus USA

How to Reset NVR and DVR without Password: CCTV Hacks - eufy UK

Note: "Traice" is often a rebranded model of generic CCTV hardware (sometimes confused with "Trassir" or "Hikvision" clones). If these steps do not work, check the bottom of the unit for a sticker with the exact model number.

Before attempting a reset, identify the specific model and firmware version of the DVR. Some Traice DVR models have a small reset

Before opening the case or calling a technician, test these common default credentials. Many Traice units ship without a unique password set.

Pro Tip: If the DVR is used or installed by a company, the password may be changed to 000000 or the installer's phone number.

Steps:

Using tweezers, move the jumper cap from pins 1-2 to pins 2-3 (or simply remove it if it’s a two-pin setup).

Wait 10 seconds. Move the jumper back to its original position.

Alternative method (older boards): If there is no jumper, look for a small black button (tactile switch). Press and hold it for 30 seconds while the DVR is powered off.

Reassemble the DVR and power it on.

Result: The DVR will boot up as if from the factory. The password will be reset to admin with no password, or admin / 12345.

Crucial Note: If the DVR was set to a static IP address, that IP will also revert to DHCP (automatic). Your NVR software on your phone/PC will lose the connection. You will need to re-add the DVR using its new IP address.