V2000-c Rfid Access Control User Manual -
You now hold the equivalent of an advanced training course for the V2000-c RFID Access Control system. This user manual has walked you from the screw terminals of the relay to the logic of anti-passback and multi-card open.
Final Pro Tips:
For further support, consult your distributor for hardware-level repairs. The V2000-c’s simplicity is its strength – there is no cloud to fail, no subscription fee, and no software to crash. Just security that works.
Document Version: 3.1
Last Updated: [Current Year]
Compatibility: All V2000-c hardware revisions H1.2 and above.
End of the V2000-c RFID Access Control User Manual.
V2000-C RFID Access Control User Manual: A Comprehensive Guide
The V2000-C RFID Access Control system is a popular, standalone security solution designed for small to medium-sized businesses, residential complexes, and secure storage areas. This guide serves as a comprehensive manual to help you install, program, and maintain your device. 1. Introduction & Specifications
The V2000-C is a single-door multifunction standalone access controller. It supports up to 2,500 users and allows access via RFID card, a 4-to-6 digit PIN, or a combination of both. Operating Voltage: DC 12V ± 10% User Capacity: 2,500 Card Reading Distance: 3–6 cm Active Current: <60mA Lock Output Load: Max 3A Operating Temperature: -45°C ~ 60°C 2. Installation and Wiring V2000-c Rfid Access Control User Manual
Before mounting, ensure the power is disconnected. The rear of the unit features a color-coded wiring harness. Description Red Positive Power Supply Black Negative Power Supply Blue Normally Open (Electronic Lock) Purple Common Terminal Orange Normally Closed (Magnetic Lock) Yellow Exit Button Input Pink Doorbell Interface 3. Programming Basics
To enter programming mode, you must use the Master Code. The factory default Master Code is 999999.
Enter Programming Mode: Press * + 999999 + #. (The indicator light will turn orange/flashing). Exit Programming Mode: Press *.
Change Master Code: Enter programming mode, then press 0 + [New 6-digit Code] + # + [Repeat New Code] + #. 4. User Management Adding Users (Card or PIN) Enter Programming Mode. Press 1. For Card: Swipe the RFID card.
For PIN: Enter a unique User ID (1-2500) + # + [4-6 digit PIN] + #. Press * to exit. Deleting Users Enter Programming Mode. Press 2. By Card: Swipe the card you wish to delete. By ID: Enter the User ID + #. Press * to exit. 5. Advanced Settings Door Relay Time
To adjust how long the door remains unlocked (0-99 seconds): Enter Programming Mode. Press 4 + [0-99] + #. (Default is 5 seconds). Access Mode Configuration You can choose how users authenticate: Card Only: Press 3 + 0 + # Card OR PIN: Press 3 + 1 + # (Default) Card + PIN: Press 3 + 2 + # 6. Resetting to Factory Defaults
If you forget the Master Code or wish to clear all settings: Power off the device. Press and hold the # key while powering the device back on. You now hold the equivalent of an advanced
Release the key after two beeps. The Master Code is now reset to 999999. 7. Troubleshooting Card not reading: Ensure the card is 125KHz EM frequency.
Constant Beeping: Check for a short circuit in the wiring or an "anti-tamper" alarm trigger.
Keypad not responding: Verify the input voltage is a steady 12V DC.
Security Tip: Always change the default Master Code immediately after installation to prevent unauthorized access to your programming settings.
Prevents a user from swiping twice to let in a tailgater.
Even with perfect installation, issues occur. Refer to this matrix.
| Error Symptom | Probable Cause | Solution |
| :--- | :--- | :--- |
| No power, no beep | Blown fuse on power supply or reverse polarity. | Check PSU, measure voltage at terminals 1 & 2 (must be 10-14V DC). |
| Card beeps but lock doesn’t open | Lock wired to wrong relay (NO vs NC). | Swap lock wire from NO to COM or NC to COM. |
| Lock opens for 1 second then closes | Insufficient power supply amperage (lock surge). | Upgrade to 12V DC 5A PSU. Add a capacitor across lock power. |
| Continuous alarm after door closes | Door contact sensor (SEN) stuck or misaligned. | Check reed switch gap (<10mm). Set 16 0 # to disable temporarily. |
| “Error” beep (two short beeps) | Command syntax error or user not found. | Re-enter command slowly. Use 14 to verify user exists. |
| Master code not accepted | Someone changed it, or keypad is faulty. | Perform emergency reset (jumper method). |
| RFID range is <1cm | Interference from metal or voltage drop. | Mount on non-metallic spacer. Check 12V at reader (terminal 2 & 10). | End of the V2000-c RFID Access Control User Manual
Access control has evolved from keyed doors and bulky card readers to sleek, secure RFID systems that balance convenience with safety. The V2000-c is a modern RFID access control unit designed for small-to-medium businesses, multi-tenant buildings, and organizations that want an affordable, reliable way to manage entry. This post walks through everything you need to know: features, installation, setup, daily use, troubleshooting, security considerations, and smart tips to get the most from your V2000-c.
(Note: this is an instructional and practical guide meant to complement the official user manual. Always consult the manufacturer’s manual and local regulations before installation.)
The V2000-c provides a practical, cost-effective entry solution for many installations. With correct installation, strict admin practices, and routine maintenance, it will deliver reliable daily operation and straightforward auditing. Balance convenience and security by using encrypted channels and two-factor methods where possible, and always comply with local egress and fire safety regulations.
If you’d like, I can:
The V2000-C RFID Access Control system provides a robust, standalone security solution for managing entry points using 125kHz EM cards or 4-digit PINs, accommodating up to 1,000 users. It features versatile, non-PC-based management for adding/deleting users and flexible wiring options for both fail-safe and fail-secure modes, suitable for small to medium-sized facilities.
The V2000-C is a "Standalone" unit, meaning it does not require a constant network connection to work, but it can connect for management.