Bmw Scanner 140 Drivers May 2026
⚠️ Caution: Many “BMW Scanner 1.4 driver” downloads from forums contain malware. Only download from trusted sources.
Recommended sources:
Typical driver file names:
If you want, I can:
(Invoking related search terms for further refinement.)
Installing drivers for the BMW Scanner 1.4.0 (also known as ) on modern 64-bit systems like Windows 10 or 11 can be tricky because the original drivers are often unsigned. 1. Download Necessary Files
You need two separate components: the software itself and the specific 64-bit drivers. BMW Scanner 1.4.0 application. bmw scanner 140 drivers
Usually provided as a "64-bit" driver folder. You can often find compatible drivers on the FTDI Chip official site (D2XX drivers). Bimmerforums.com 2. Enable Test Mode (Required for 64-bit)
Because the drivers are often unsigned, Windows will block them unless you enable Command Prompt as an Administrator. bcdedit /set testsigning on and press Enter. Restart your PC
. You should see "Test Mode" in the bottom-right corner of your desktop. 3. Install the Drivers Manually Do not rely on the automatic installer; use the Device Manager Slideshare
BMW scanner 1.4 installation tutorial for Windows 10. (PA Soft)
Installing drivers for the BMW Scanner 1.4.0 (often called PA Soft) can be tricky on modern 64-bit systems like Windows 10 or 11. Most issues stem from the fact that the original drivers were intended for 32-bit Windows XP. Essential Installation Steps To get the scanner working correctly, follow this sequence:
Download 64-Bit Drivers: Standard discs often only include 32-bit drivers. You typically need to download the D2XX drivers directly from the FTDI Chip Drivers Page. Installation steps (Windows):
Plug-In Sequence: Plug the scanner into the car's OBD port first to power it (look for a solid green light), and then connect the USB to your computer.
Manual Update: Open Device Manager, find the "BMW Scanner" device (it will likely have a yellow exclamation mark), right-click it, and select "Update Driver".
Disable Driver Signature Enforcement: On Windows 10/11, you may need to disable "test signing" or driver signature enforcement to allow the unofficial drivers to load. Use the command prompt as an admin and run bcdedit /set testsigning on, then restart your PC. Common Error Fixes
"Connection Error with IKE/EWS": If the software opens but won't talk to the car, you might need to solder pins 7 and 8 together inside the scanner cable, as some aftermarket cables come with these disconnected.
"Access Violation": This often happens if you try to run the software before the drivers are fully recognized by Windows.
64-Bit Compatibility: If you're on a 64-bit system, ensure you specifically point the Device Manager to the folder containing the ftdibus.inf and ftdiport.inf files. Where to Find Help ⚠️ Caution: Many “BMW Scanner 1
Important Pre-Read: This software and interface are from the Windows XP/7 era. The most stable experience is on Windows 7. It works on Windows 10 and 11, but it requires disabling "Driver Signature Enforcement," which lowers your system security slightly during the install.
BMW Scanner 140 is an older, popular diagnostic interface used to read and clear fault codes and view live data on many BMW models (mostly pre-2005 E-series and some early E46/E39 vehicles). It connects to a PC via serial (RS-232) or USB (with a serial-to-USB adapter) and uses dedicated software to communicate with the car’s ECU and submodules.
Follow this guide carefully. Do not plug in the scanner until instructed.
Even after installation, problems occur. Below is a troubleshooting table.
| Symptom | Likely Cause | Solution | |---------|--------------|----------| | "Interface not found" in PA Soft | Wrong COM port or driver conflict | Force COM port to COM1-4 in Device Manager > Advanced | | Yellow exclamation mark in Device Manager | Counterfeit FTDI chip blocked by new driver | Downgrade FTDI driver to version 2.12.24 or use Zadig tool to install libusb | | Driver installs but car connection fails | Baud rate mismatch | In Device Manager, change baud rate to 9600, 8 data bits, 1 stop bit, no parity | | Windows keeps overwriting driver | Automatic driver updates enabled | Go to System Properties > Hardware > Device Installation Settings > "No" | | Scanner works once then disappears | USB selective suspend | Disable USB selective suspend in Power Options > Advanced settings |
| OS | Compatibility | Notes | |----|--------------|-------| | Windows XP | Full | Ideal, most stable | | Windows 7 (32/64-bit) | Good | May require legacy driver mode | | Windows 8/8.1 | Limited | Manual driver installation needed | | Windows 10 (32/64-bit) | Partial | Requires signed or test mode drivers | | Windows 11 | Unreliable | Not officially supported |
⚠️ 64-bit Windows requires driver signature enforcement to be disabled or use specially modified drivers.